Solution
Builds in-house pre-compliance testing capability at a controlled cost, enabling early detection of surge, EFT/burst, ESD, voltage-dip, and conducted-emission issues.
The high-precision programmable power supply HPS-XXXX series is mainly used in electrical performance testing of automotive electronic equipment and electrical load testing of electronic and electrical components, battery charge and discharge and ripple heating testing, capacitor material testing, electroplating processing and other fields. It has a four-quadrant operating mode, can both provide power and absorb power, and can drive inductive loads and capacitive loads. It has the advantages of output accuracy and low drift at high temperatures, with a minimum programmable time of 3μs in steps of 1μs, which can easily achieve fast programming output, and the output bandwidth ranges from DC to 500kHz. It also supports arbitrary waveforms and can be combined with common waveforms for output. The integrated external voltage detection function can be used as a closed-loop Vpp output to meet the ripple superposition test requirements of ISO16750-2-2023. With the corresponding current and boost transformers, it can
Static electricity between the human body and an object or between two objects can sometimes produce a voltage of tens of thousands of volts, which may cause circuit malfunction or even damage to electrical and electronic equipment. The electrostatic discharge simulator ESD-20A is an advanced intelligent electrostatic discharge generator with a maximum output voltage of 20kV. It is also an independently developed and produced electrostatic discharge simulator that integrates discharge gun head and touch screen control. The LCD touch screen is simple and easy to operate, and the RC module is replaceable, ensuring reliability in various testing situations. According to standards: ISO 10605, GB/T 19951, GB/T17626.2, IEC61000-4-2, etc.
Industrial measurement or control equipment may contain relays or some mechanical switching devices. Those using the public power supply system are usually fluorescent lamp ballasts or some small-power electrical appliances. These electrical appliances have inductive loads and will cause interference when switching on and off. Electrical fast transients can cause a microprocessor to malfunction or reset, preventing normal operation. The intelligent electrical fast transient burst simulator EFT-45X series is specially designed according to the characteristics and requirements of electrical and electronic products for electrical fast transient burst testing. It has a built-in coupling and decoupling network for the main power supply line of the single-phase or three-phase equipment under test. It has the characteristics of good reliability, stable performance, and easy use. According to standards: EN61000-4-4 and GB/T17626.4, etc.
The lightning surge generator SUG-562 is a high-end test equipment specially designed to simulate the phenomenon of surge pulse interference. Its performance fully meets the EU CE certification and CCC certification immunity test requirements for single-phase equipment under test. Through the built-in coupling decoupling network, the power port of the equipment under test is surge tested, and the communication line can be surge tested through the external network. According to standards: IEC61000-4-5, EN61000-4-5 and GB/T17626.5, etc.
Voltage sags and short-term interruptions are caused by failures of the power grid and power facilities or sudden large changes in load. In some cases there will be two or more consecutive dips or interruptions. Voltage changes are caused by continuous changes in the loads connected to the grid. If the EUT cannot respond in time to changes in the power supply voltage, it may cause failure. Voltage Drop Simulator VOD-1110 is used to evaluate the performance of electrical and electronic equipment when subjected to voltage sags, short interruptions and voltage changes. According to standards: IEC61000-4-11 and GB/T17626.11, etc.
The RF conducted immunity test system CSR-608 adopts an integrated design with built-in signal synthesizer, power meter, RF power amplifier dual directional coupler (optional), etc. It can output CW, AM, PM and other modulated or unmodulated RF signals from 100kHz to 300MHz. The wide input range power meter can detect power signals from -85DBm to 10DBm without interruption. Selectable average mode or pulse mode to handle detecting amplitude modulated or pulse modulated signals. Each part can work independently, and an external power amplifier can be used. The truly one-piece design makes calibration faster, and all frequency points can be calibrated in tens of seconds. The RF conducted immunity test system CSR-608 is used for conducted immunity testing of civilian products. According to standards: IEC61000-4-6 and GB/T 17626.6, etc.
Builds an R&D pre-compliance test platform at low cost.
Identifies electromagnetic interference issues early in the development stage.
Avoids repeated corrective actions after third-party testing and significantly shortens time to market.
